Productclaude-opus-5-5

Two-Angle Desk Phone Stand

A desk phone stand in two printed parts with no screws or glue: a solid 88 × 88 mm base with two angled sockets, and an L-shaped cradle that drops into either one. The front socket sets a 55° reading angle and the rear socket a 70° video-call angle. A slot through the cradle's ledge and a notch in the base let the charging cable stay plugged in, leaving forward over the desk or backward through a channel underneath. It fits phones 65–80 mm wide and up to 11 mm thick in a case, and both parts print in PLA without supports.

Remix

How it was made

Recorded: a creator-reviewed session, November 12, 2026.

Models

  • claude-opus-5-5 · anthropic · execution · Claude Code

Agent

Claude Code

Tools and APIs

  • CadQuery

    Model both parts parametrically and export the STEP and STL files.

  • trimesh

    Check interference, phone and plug clearances, watertightness and overhangs on the meshes.

  • matplotlib

    Render the assembled, side, exploded and base views.

  • Write

    Write the parametric model, the check and statics scripts and the report.

  • Read

    Check the renders and check results between fixes.

  • Possible job runner

    Receive the brief, run the CAD build, checks and renders on a remote machine and hand back the result.

Ordered steps

  1. Give Prototype Engineer a three-part brief

    Fill in the agent's brief: what it should be, the sizes, loads and limits, and how it will be made. The agent designed, checked and documented the part without follow-ups.

    What should it be? A desk phone stand that holds a phone at two viewing angles (for video calls and for reading), with a slot so the charging cable can stay plugged in.
    
    Sizes, loads and limits: fits phones 65–80 mm wide and up to 11 mm thick, including in a case; stays put when tapping the screen; footprint under 90 × 90 mm.
    
    How will it be made? FDM printing in PLA on a 220 mm bed, without supports, and no screws or glue.

Made with the Prototype Engineer skill

See the skill

US$19 for this skill.

Buy the Prototype Engineer skill

One payment, then you download it. It runs on your own machine, in Claude Code or Codex, with your own subscription.

By buying, you agree to our Terms and Refund Policy. Your purchase is sold through Link, a Stripe company, which takes your payment.

About

A desk phone stand in two printed parts with no screws or glue: a solid 88 × 88 mm base with two angled sockets, and an L-shaped cradle that drops into either one. The front socket sets a 55° reading angle and the rear socket a 70° video-call angle. A slot through the cradle's ledge and a notch in the base let the charging cable stay plugged in, leaving forward over the desk or backward through a channel underneath. It fits phones 65–80 mm wide and up to 11 mm thick in a case, and both parts print in PLA without supports.

How it was made

An AI agent made this. Prototype Engineer, a Possible skill run in Claude Code with Claude Opus 5.5, got the brief shown here and nothing else: a fresh, empty workspace and no follow-ups. It wrote a parametric CadQuery model, then built, checked and rendered it on a remote Linux machine. The final build passed all 50 of its geometry checks: valid solids, no interference in either position, three phone sizes and a charging plug clear of the parts, footprint, bed size and overhangs. It dropped an earlier hinged-kickstand concept after its own statics showed the hinge would lift under a large phone. Possible recorded the session with possible capture. Nobody edited the model by hand.

What to know

This is a digital pre-build only. Nothing has been printed or measured. The tap-stability figures are calculations from an assumed 1 N tap and an assumed desk friction of 0.3; with a solid base the margin near the top of a large phone is thin, and at lower infill a tap there could tip it. The two angles and the plug size are the agent's assumptions, and the report lists the physical tests needed before relying on it. The renders are plain mesh plots, not photorealistic. The brief is public; the agent's standing instructions are not. Results vary between runs.

Exact prompt

Hidden characters, if present, appear as Unicode escapes
What should it be? A desk phone stand that holds a phone at two viewing angles (for video calls and for reading), with a slot so the charging cable can stay plugged in.

Sizes, loads and limits: fits phones 65–80 mm wide and up to 11 mm thick, including in a case; stays put when tapping the screen; footprint under 90 × 90 mm.

How will it be made? FDM printing in PLA on a 220 mm bed, without supports, and no screws or glue.

What you need

  • Claude Code, or another coding agent that can write files and run Python
  • CadQuery, trimesh and matplotlib to rebuild, check and render the model
  • A CAD viewer for the STEP files and a slicer for the STL files
FILES

Download the result

Technical details and provenance
Provider
anthropic
Model
claude-opus-5-5
Agent
Claude Code
Published
Publication
Made by Possible